ESP8266 NodeMCU (Amica Clone)

$9.90

The ESP8266 NodeMCU (Amica Clone) is a low-cost Wi-Fi development board based on the ESP8266-12E (ESP-12E) Wi-Fi module.
It’s designed for IoT (Internet of Things) projects, allowing you to connect sensors, actuators, and devices to the internet easily.

$9.90

The ESP8266 NodeMCU (Amica Clone) is a low-cost Wi-Fi development board based on the ESP8266-12E (ESP-12E) Wi-Fi module.
It’s designed for IoT (Internet of Things) projects, allowing you to connect sensors, actuators, and devices to the internet easily.

The “Amica” version (or clone) refers to a board layout originally made by Amica — one of the earliest and most reliable NodeMCU board manufacturers.
Many “Amica clones” are now made by third parties but use the same design and pinout, making them fully compatible with Arduino IDE and Lua firmware.

Key Features

Feature Description
Wi-Fi Connectivity Integrated 2.4 GHz Wi-Fi (802.11 b/g/n) with TCP/IP stack.
Microcontroller Tensilica L106 32-bit RISC CPU, 80 MHz (can overclock to 160 MHz).
Flash Memory Typically 4 MB (varies between 512 KB – 16 MB in some clones).
Programming Interface Micro-USB interface with onboard CP2102 or CH340 USB-to-Serial converter.
GPIO Pins 11 usable GPIOs (GPIO0–GPIO16, with some limitations).
Analog Input 1 × ADC input (0–1.0 V).
Communication Interfaces UART, SPI, I²C (software), and PWM supported.
Firmware Options Supports Arduino IDE, MicroPython, NodeMCU (Lua), PlatformIO, etc.
Power 5 V via USB or 3.3 V via VIN pin. Onboard regulator outputs 3.3 V for ESP8266.
Reset & Flash Buttons Two buttons on board (RESET and FLASH).
Breadboard-Friendly Designed to fit directly on a breadboard for easy prototyping.

Specifications

Parameter Value
Microcontroller ESP8266EX
Architecture 32-bit RISC (Tensilica L106)
Operating Voltage 3.3 V (logic), 5 V via USB
Flash Memory 4 MB typical
SRAM 80 KB user data + 36 KB instruction RAM
Clock Frequency 80 MHz (default), 160 MHz (overclock)
Wi-Fi Protocols IEEE 802.11 b/g/n (2.4 GHz)
Wi-Fi Security WPA/WPA2
Max Wi-Fi Speed ~72 Mbps (theoretical)
I/O Pins 11 digital GPIOs (PWM, I2C, SPI, UART)
Analog Input (ADC) 1 channel, 10-bit resolution (0 – 1 V)
USB Interface CP2102 / CH340G USB-to-Serial converter
Operating Current 70 – 200 mA (depending on Wi-Fi activity)
Deep Sleep Current < 20 µA
Dimensions ~49 mm × 26 mm
Weight ~8 g

Pinout Overview

Common NodeMCU (Amica) pin mapping:

Label ESP8266 GPIO Notes
D0 GPIO16 No interrupt, no PWM, no I2C
D1 GPIO5 SCL (I²C default)
D2 GPIO4 SDA (I²C default)
D3 GPIO0 Must be HIGH on boot
D4 GPIO2 Connected to onboard LED
D5 GPIO14 SPI CLK
D6 GPIO12 SPI MISO
D7 GPIO13 SPI MOSI
D8 GPIO15 Must be LOW on boot
RX GPIO3 UART RX
TX GPIO1 UART TX
A0 ADC0 0 – 1 V analog input

Programming Options

  1. Arduino IDE (most popular)

    • Select: Tools > Board > NodeMCU 1.0 (ESP-12E Module)

    • Connect via USB and select correct COM port.

    • Use libraries for Wi-Fi, MQTT, sensors, etc.

  2. MicroPython

    • Flash MicroPython firmware using esptool.py.

    • Use Thonny IDE or uPyCraft to upload code.

  3. NodeMCU (Lua)

    • Original firmware; can use Lua scripts to control hardware and Wi-Fi.

  4. PlatformIO

    • For advanced users who prefer VSCode integration and modular build system.

Tips and Best Practices

  1. Power Supply

    • The ESP8266 is sensitive to voltage drops — use a stable 5 V USB supply or 3.3 V regulator (≥ 500 mA).

    • Brownout or unstable Wi-Fi = power issues.

  2. Boot Modes

    • GPIO0, GPIO2, and GPIO15 determine boot mode:

      • GPIO0 = LOW → flash mode

      • GPIO0 = HIGH → run mode

    • The “Flash” button pulls GPIO0 low for programming.

  3. ADC Precaution

    • ADC0 input range is 0 – 1.0 V (use a voltage divider if measuring higher voltages).

  4. Deep Sleep

    • Connect GPIO16 → RESET pin to enable wake-up from deep sleep.

  5. Serial Monitor Settings

    • Use 115200 bps baud rate for most firmwares.

  6. Wi-Fi Range

    • Range up to 100 m (open air); keep antenna clear of metal and ground planes.

  7. Common Issues

    • Upload failed? → Check COM port, correct board, and that GPIO0 is LOW when flashing.

    • WDT Reset? → Avoid blocking delays; use non-blocking code or yield() in loops.

Example: Basic Arduino Sketch

#include <ESP8266WiFi.h>

const char* ssid = “YourWiFiName”;
const char* password = “YourWiFiPassword”;

void setup() {
Serial.begin(115200);
WiFi.begin(ssid, password);
Serial.println(“\nConnecting…”);

while (WiFi.status() != WL_CONNECTED) {
delay(500);
Serial.print(“.”);
}

Serial.println(“\nWiFi connected!”);
Serial.print(“IP Address: “);
Serial.println(WiFi.localIP());
}

void loop() {
// Your main code
}

Applications

  • IoT sensors (temperature, humidity, etc.)

  • Smart home automation

  • Wi-Fi relays and switches

  • Web servers / REST API devices

  • Remote data logging

  • MQTT / Blynk / ThingSpeak projects

Based on 0 reviews

0.0 overall
0
0
0
0
0

Only logged in customers who have purchased this product may leave a review.

There are no reviews yet.

Related Products