The SMIH-05VDC-SL-C is an 8-pin, 5V DC, double-pole double-throw (DPDT) electromagnetic relay.
It works as an electrically controlled switch that can control two independent circuits simultaneously — each with a Common (COM), Normally Open (NO), and Normally Closed (NC) contact.
This makes it ideal for tasks like motor polarity reversing, signal routing, dual-circuit switching, and automation logic.
Key Features
| Feature | Description |
|---|---|
| Type | Electromagnetic DPDT relay |
| Coil Voltage | 5 V DC |
| Number of Pins | 8 (2 coil pins + 6 contact pins) |
| Contact Form | 2 Form C (DPDT — 2x SPDT) |
| Contact Rating | 5A @ 250 VAC / 5A @ 30 VDC |
| Coil Power | ~0.36 W |
| Mounting Type | PCB mounting |
| Contact Material | Silver Alloy |
| Operate Time | ≤ 10 ms |
| Release Time | ≤ 5 ms |
| Dielectric Strength | 1500 VAC (coil to contacts) |
| Insulation Resistance | ≥ 100 MΩ @ 500 VDC |
| Mechanical Life | 10 million operations |
| Electrical Life | 100,000 operations @ rated load |
| Operating Temperature | -40°C to +85°C |
Pin Configuration (8 Pins)
Explanation:
-
The relay has two independent switches inside (Channel 1 and Channel 2).
-
When the coil is not energized → COM1→NC1 and COM2→NC2 are connected.
-
When energized → COM1→NO1 and COM2→NO2 connect.
Electrical Characteristics
| Parameter | Typical Value |
|---|---|
| Coil Voltage (Nominal) | 5 V DC |
| Coil Resistance | 70 ±10% Ω |
| Coil Current | ≈ 71 mA |
| Pull-in Voltage (Max) | ≤ 3.75 V |
| Drop-out Voltage (Min) | ≥ 0.5 V |
| Max Coil Voltage | 6.5 V DC |
| Contact Resistance | ≤ 100 mΩ |
| Insulation Resistance | ≥ 100 MΩ |
| Contact Rating | 5 A @ 250 VAC / 30 VDC |
| Dielectric Strength | 1500 VAC (Coil–Contacts) |
| Contact Form | DPDT (2 Form C) |
Tips for Use
-
Use a transistor or relay driver (e.g., 2N2222, BC547, or ULN2003) — do not drive the coil directly from a microcontroller pin.
-
Add a flyback diode (1N4007) across the coil to protect your control circuit from voltage spikes.
-
Use both poles if you want to reverse DC motor direction (H-bridge logic).
-
Avoid high-frequency switching to prevent contact wear.
-
Allow proper ventilation — relays generate some heat during continuous operation.
-
Double-check pinout orientation before soldering — some boards label pins differently.
Applications
-
DC motor forward/reverse control
-
Dual load switching (two circuits simultaneously)
-
Signal routing or audio switching
-
PLC control and automation systems
-
Home appliances or IoT control
-
Safety interlocks and control logic systems
Example: Using SMIH-05VDC-SL-C for DC Motor Direction Control
| Relay Contact | Function |
|---|---|
| COM1, COM2 | Motor terminals |
| NO1/NC1, NO2/NC2 | Connected to V+ and GND in reverse polarity pairs |
| Coil pins | Driven via NPN transistor controlled by MCU |
When the relay is OFF → motor spins forward.
When the relay is ON → motor spins in reverse.
Example Arduino Circuit
Connections:
-
Relay coil (+) → +5V
-
Relay coil (–) → NPN transistor collector
-
Transistor base → Arduino pin (via 1kΩ resistor)
-
Flyback diode across relay coil
-
COM1 & COM2 → Motor terminals
-
NC1/NO1, NC2/NO2 → VCC/GND (crossed to reverse polarity)
Example Arduino Code
Quick Summary Table
| Parameter | Value |
|---|---|
| Model | SMIH-05VDC-SL-C |
| Coil Voltage | 5 V DC |
| Coil Resistance | ~70 Ω |
| Coil Current | ~70 mA |
| Coil Power | 0.36 W |
| Contact Type | DPDT (2 Form C) |
| Contact Rating | 5 A @ 250 VAC / 30 VDC |
| Operate / Release Time | ≤10 ms / ≤5 ms |
| Mounting | PCB |
| Dimensions | ~19 × 15.5 × 15 mm |
| No. of Pins | 8 |
| Insulation Resistance | ≥100 MΩ |






There are no reviews yet.