SMIH-12VDC-SL-C 8Pins Relay

$2.25

The SMIH-12VDC-SL-C is a miniature electromagnetic relay designed to control two independent circuits (DPDT) with a 12 V DC coil.

$2.25

The SMIH-12VDC-SL-C is a miniature electromagnetic relay designed to control two independent circuits (DPDT) with a 12 V DC coil.
It allows a low-power control circuit (like a microcontroller, PLC, or sensor output) to safely switch AC or DC loads — such as motors, lamps, heaters, and solenoids — on or off.

This relay is part of the Songle-type SMIH series, known for compact size, reliability, and suitability for industrial control, home automation, and robotics.

Key Features

Feature Description
Relay Type Electromagnetic DPDT relay
Contact Form 2 Form C (2 × SPDT change-over contacts)
Coil Voltage 12 V DC
Number of Pins 8 pins (2 coil + 6 contact)
Contact Rating 5 A @ 250 VAC / 5 A @ 30 VDC
Coil Power Consumption ≈ 0.36 W
Mounting Type PCB mount
Contact Material Silver Alloy
Operate Time ≤ 10 ms
Release Time ≤ 5 ms
Insulation Resistance ≥ 100 MΩ @ 500 VDC
Dielectric Strength 1500 VAC (1 min between coil & contacts)
Mechanical Life 10 million ops
Electrical Life 100 000 ops @ rated load
Operating Temp −40 °C to +85 °C

Pin Configuration (Bottom View)

+--------------------------------+
| 1 2 3 4 5 6 7 8 |
+--------------------------------+
Pin Function Description
1 Coil (+) Connect to +12 V DC
8 Coil (–) Connect to GND (or driver transistor)
2 COM1 Common contact for Pole 1
3 NC1 Normally Closed (Pole 1)
4 NO1 Normally Open (Pole 1)
5 COM2 Common contact for Pole 2
6 NC2 Normally Closed (Pole 2)
7 NO2 Normally Open (Pole 2)

Operation:

  • De-energized: COM1 → NC1 and COM2 → NC2

  • Energized: COM1 → NO1 and COM2 → NO2

Electrical Specifications

Parameter Typical Value
Nominal Coil Voltage 12 V DC
Coil Resistance ≈ 400 Ω (±10 %)
Nominal Coil Current ≈ 30 mA
Pull-in Voltage (max) ≤ 9 V DC
Drop-out Voltage (min) ≥ 1.2 V DC
Max Coil Voltage 15.6 V DC
Contact Rating 5 A @ 250 VAC / 30 VDC
Contact Resistance ≤ 100 mΩ
Insulation Resistance ≥ 100 MΩ @ 500 VDC
Operate / Release Time ≤ 10 ms / ≤ 5 ms
Dielectric Strength 1500 VAC (coil-contacts)
Dimensions ≈ 19 × 15.5 × 15 mm

Usage Tips

  1. Use a flyback diode (e.g., 1N4007) across the coil terminals to protect driver circuits.

  2. Drive via transistor or relay-driver IC (e.g., 2N2222, BC547, ULN2003) — coil current (~30 mA) is too high for direct microcontroller output.

  3. Stable 12 V supply — avoid voltage drops; relays may chatter below 9 V.

  4. Avoid rapid switching — mechanical wear shortens lifespan.

  5. Cross-check pinout before soldering; bottom view orientation can differ between PCB footprints.

  6. Do not exceed contact ratings; for inductive loads, add snubber or MOV protection.

Applications

  • Dual-circuit switching and signal routing

  • DC motor forward/reverse control

  • Robotics and automation logic

  • Smart home and IoT control systems

  • Industrial controllers and PLC interfaces

  • Power and audio signal selection switching

Example Arduino Connection

Arduino Pin Component Connection
D7 → 1 kΩ → NPN base (2N2222)
Collector → Relay coil (–)
Relay coil (+) → +12 V
Emitter → GND
Flyback diode Across coil (1N4007)
COM1/COM2 → Load terminals
NO1/NO2 → Power source (12 V or AC)

Example Arduino Code

#define RELAY_PIN 7 // Pin driving transistor base

void setup() {
pinMode(RELAY_PIN, OUTPUT);
}

void loop() {
digitalWrite(RELAY_PIN, HIGH); // Energize relay
delay(2000);
digitalWrite(RELAY_PIN, LOW); // De-energize relay
delay(2000);
}

Quick Summary

Parameter Value
Model SMIH-12VDC-SL-C
Coil Voltage 12 V DC
Coil Resistance ≈ 400 Ω
Coil Current ≈ 30 mA
Contact Form DPDT (2 Form C)
Contact Rating 5 A @ 250 VAC / 30 VDC
Operate Time ≤ 10 ms
Release Time ≤ 5 ms
Mounting PCB
No. of Pins 8
Mechanical Life 10 million ops

Specifications :

Specification Description
Relay Type Electromagnetic DPDT relay
Contact Form 2 Form C (2 × SPDT change-over contacts)
Coil Voltage 12 V DC
Number of Pins 8 pins (2 coil + 6 contact)
Contact Rating 5 A @ 250 VAC / 5 A @ 30 VDC
Coil Power Consumption ≈ 0.36 W
Mounting Type PCB mount
Contact Material Silver Alloy
Operate Time ≤ 10 ms
Release Time ≤ 5 ms
Insulation Resistance ≥ 100 MΩ @ 500 VDC
Dielectric Strength 1500 VAC (1 min between coil & contacts)
Mechanical Life 10 million ops
Electrical Life 100 000 ops @ rated load
Operating Temp −40 °C to +85 °C

Based on 0 reviews

0.0 overall
0
0
0
0
0

Only logged in customers who have purchased this product may leave a review.

There are no reviews yet.

Related Products