Ultra-small 12V DPDT Relay Module

$4.50

$4.50

The Ultra-small 12V DPDT Relay Module is a compact electromechanical polarity reversing switch that allows you to change the direction of current flow through a DC device (like a motor).

When the relay is de-energized, the motor runs in one direction; when energized, the relay reverses the polarity, causing the motor to spin in the opposite direction.

This makes it a simple, low-cost alternative to an electronic H-Bridge (like L298N or L293D) when only direction control (not speed control) is needed.

Key Features

Feature Description
Operating Voltage 12V DC (relay coil and driver circuit)
Relay Type DPDT (Double Pole Double Throw)
Channel Count 1
Polarity Reversal Function Yes — changes motor direction
Control Signal Logic-level input (can be triggered by microcontroller or switch)
Control Logic Active HIGH (12V → ON, 0V → OFF)
Indicator LED Shows relay ON/OFF status
Protection Flyback diode for coil protection
Size Ultra-small compact board (approx. 25 × 15 × 18 mm)
Mounting Through-hole or via screw terminal (depending on version)

Working Principle

This module uses a DPDT relay to cross-wire the polarity of your DC load (e.g., motor).

  • When relay is OFF → COM is connected to NC → motor spins forward.

  • When relay is ON → COM is connected to NO → motor spins reverse.

So one control signal toggles between forward and reverse rotation.

Electrical Specifications

Parameter Typical Value
Operating Voltage 12 V DC
Trigger Current 20–40 mA (signal input)
Relay Coil Current 60–80 mA
Relay Contact Rating 2A–5A @ 30VDC / 250VAC
Relay Coil Power ≈ 0.36 W
Contact Resistance ≤ 100 mΩ
Insulation Resistance ≥ 100 MΩ
Operate Time ≤ 10 ms
Release Time ≤ 5 ms
Operating Temperature –40°C to +85°C
Service Life >100,000 cycles (mechanical)

Pin Configuration

Depending on the board design (header pins or screw terminals), the pins are typically arranged as follows:

Pin Label Description
1 VCC +12V power supply
2 GND Ground
3 IN Signal input (HIGH = ON, LOW = OFF)
4 COM1 Common terminal 1 (to one motor wire)
5 NO1 Normally Open 1
6 NC1 Normally Closed 1
7 COM2 Common terminal 2 (to other motor wire)
8 NO2 Normally Open 2
9 NC2 Normally Closed 2

Tips for Proper Use

  1. Don’t use for PWM/speed control — this relay switches mechanically, suitable only for direction switching.

  2. Use flyback diode across the motor terminals if not built in, to prevent voltage spikes.

  3. Ensure 12V stable power — relay coil requires full 12V for reliable switching.

  4. Use correct wiring — cross NO/NC pairs to achieve polarity reversal.

  5. Keep logic and power grounds common if triggered from microcontroller.

  6. Check load current — if your motor exceeds 2–3A continuous, use a relay rated for higher current.

  7. Avoid rapid switching — mechanical relays have limited switching speed and life.

Applications

  • DC Motor Direction Control (Forward/Reverse)

  • Linear Actuator Polarity Switching

  • Door Lock/Solenoid Control

  • DIY Robotics and Automation Projects

  • RC Boat, Car, or Winch Direction Control

  • Home Automation Systems

Typical Wiring for DC Motor

Power Section:

  • Connect VCC = 12V

  • Connect GND = Power ground

Load Section:

Relay Pin Connection
COM1, COM2 To motor terminals
NO1 → NC2 Cross-connected
NO2 → NC1 Cross-connected
NO1 & NO2 Connected to +12V and GND (reversed polarity pair)

When relay switches, it flips the polarity → motor direction reverses.

Example Arduino (or ESP32/ESP8266) Code

(Using a transistor or optocoupler interface, since relay coil is 12V)

#define RELAY_PIN 7 // Control pin through transistor driver

void setup() {
pinMode(RELAY_PIN, OUTPUT);
}

void loop() {
digitalWrite(RELAY_PIN, HIGH); // Relay ON → Reverse
delay(2000);
digitalWrite(RELAY_PIN, LOW); // Relay OFF → Forward
delay(2000);
}

If you connect it directly to a 12V switch instead of a microcontroller, you can control direction manually without programming.

Summary Table

Parameter Value
Model Ultra-small DPDT 12V 1-Channel Relay Module
Type Polarity Reversal Switch
Relay Type Double Pole Double Throw (DPDT)
Input Voltage 12V DC
Load Voltage 30VDC / 250VAC max
Load Current 2–5A
Control Logic Active HIGH
Indicator LED Yes
Coil Current ~70 mA
Driver Circuit Built-in transistor and flyback diode
Applications DC motor direction, linear actuators, solenoids
Size Compact (approx. 25 × 15 × 18 mm)

Based on 0 reviews

0.0 overall
0
0
0
0
0

Only logged in customers who have purchased this product may leave a review.

There are no reviews yet.