2 Channel Relay Module
$3.60
2 Channel Relay Module for control Board Arduino Uno R3 Raspberry Pi
$3.60
This is a 2 Channel Relay interface board of 5v, Be able to control various appliances(Example Lamp, Motor and other equipment with large current). It can be controlled directly by Microcontroller(for arduino , 8051)
- Â 5V 2-Channel Relay interface board, and each one needs 15-20mA Driver Current
- Â Equipped with high-current relay, AC250V 10A ; DC30V 10A
- Â Standard interface that can be controlled directly by microcontroller (8051, AVR, PIC, DSP, ARM, ARM, MSP430, TTL logic)
This module acts like an electrically operated switch. You send a low-level signal (like 3.3V or 5V) from your microcontroller to turn ON or OFF high-power devices safely.
Pinout Overview
| Pin Label | Function |
|---|---|
| VCC | Connect to 5V (or 3.3V for some versions) |
| GND | Ground |
| IN1 | Signal to control Relay 1 (LOW = ON) |
| IN2 | Signal to control Relay 2 (LOW = ON) |
-
NO (Normally Open) – open when relay is off
-
COM (Common) – connects to load power
-
NC (Normally Closed) – closed when relay is off
How It Works (Control Logic)
-
Send LOW signal (e.g.,
digitalWrite(pin, LOW)in Arduino) to IN1 or IN2 → relay switches ON. -
Send HIGH signal → relay turns OFF.
Example: Connecting to ESP32 or Arduino
int relay1 = 5; // GPIO5
int relay2 = 18; // GPIO18void setup() {pinMode(relay1, OUTPUT);
pinMode(relay2, OUTPUT);
digitalWrite(relay1, HIGH); // Relay OFF
digitalWrite(relay2, HIGH); // Relay OFF
}
void loop() {digitalWrite(relay1, LOW); // Relay ON
delay(1000);
digitalWrite(relay1, HIGH); // Relay OFF
delay(1000);
}
Safety Tips
-
Relays can switch high-voltage AC — always insulate properly.
-
Never touch the high-voltage side when powered.
-
Use flyback diodes if switching DC inductive loads (motors, solenoids).
-
If using with ESP32 (3.3V), make sure relay module supports 3.3V logic, or use a level shifter or transistor.
If you want to see how you can connect it, watch this video can be helpful for you.
Features:
- Usage:Â General Purpose
- Contact Load:Â High Power
- Theory:Â Voltage Relay
- Model Number:Â Relay Module
- is_customized:Â Yes
- Protect Feature:Â Epoxy
- Power Source:Â DC
- Voltage:Â Other
- Size:Â 6mm*38.8mm*19.3mm
- dc controller relay remote
- Type:Â Voltage Regulator
- Condition:Â New
- Application:Â Computer
- Supply Voltage:Â 5V
- Dissipation Power:Â 300W
- Operating Temperature: -40 -85℃
- Model Number:Â 2 Channel 5V Relay Optocoupler
- is_customized:Â Yes
Specifications :
| Parameter | Details |
|---|---|
| Channels | 2 (can control 2 devices) |
| Relay Type | Electromechanical SPDT (1C/O) |
| Input Voltage | 5V (some versions 3.3V or 12V) |
| Trigger Level | LOW-level (active LOW, usually) |
| Relay Output Voltage | Up to 250V AC or 30V DC |
| Max Load Current | Typically 10A per channel |
| Isolation | Optocoupler (for MCU safety) |
| Indicators | LEDs to show relay ON/OFF state |
| Terminals | Screw terminals for output load |
Based on 1 review
Only logged in customers who have purchased this product may leave a review.
Related Products
Related products
Related products
-
Uncategorized
4 * 4 Matrix Array Matrix Keypad
0 out of 5(0)Keypad 4*4 is used for loading into the microcontroller. It consists of 16 buttons arranged in a form of an array containing four lines and four columns.it is connected to the development system by regular IDC 10 female connector plugged in some development system’s port.
SKU: n/a








KennethSmari –
I like it. Good components
KennethSmari –