-7%

AC 220V STC-3028 Digital Temperature Controller STC3028

$12.60 $13.50

Be able to connect with humidifier and dehumidifier equipment at the same time.

Be able to connect with refrigeration/ heating and humidifier/dehumidifier equipment at the same time.

Heating/Cooling function could be set separately for refrigeration and heating to protect temperature controller from violent change. Same as humidity Control.

Supporting Temp and Humidity Calibration

Dual Display Window,Be able to display measured temperature/humidity and set temp/humidity at the same time

$12.60 $13.50

$49.50 for 3 item(s)

The STC-3028 is a dual-display AC 220V digital temperature and humidity controller often used in incubators, greenhouses, and other HVAC or environmental control systems.

Introduction – STC-3028

The STC-3028 is a smart, programmable controller with:

  • Temperature sensor

  • Humidity sensor

  • Separate relay outputs for temperature and humidity control

  • An intuitive LED display and keypad interface

It’s ideal for applications where you need to maintain a stable environment automatically.

 Key Features

  • Dual relay control: one for temp, one for humidity

  • Wide temperature and humidity sensing range

  • User-configurable setpoints and hysteresis

  • °C/°F switchable (some versions)

  •  Buzzer/alarm function for out-of-range values

  •  Bright dual digital display

  •  Compact and easy to install

4. Typical Applications

  • Poultry incubators

  • Greenhouses

  • Mushroom farming

  • HVAC systems

  • Humidors and dehumidifiers

  • Storage room environmental control

5. Wiring Summary

Back side terminals typically labeled:

Terminal Use
1 & 2 Power input (AC 220V)
3 & 4 Relay output for temp
5 & 6 Relay output for RH
7 Sensor signal (data)
8 Sensor power (VCC)
9 Sensor ground (GND)

 Always confirm the actual pinout on your unit before connecting.

Setting Target Temperature & Humidity

  • Set temperature: Press “SET” → adjust with ▲▼ → long press “SET” to confirm

  • Set humidity: Usually through a mode switch (check manual or hold button)

  • Set hysteresis (range), high/low alarms: Available through parameter menu (hold buttons for 3–5s)

Important Safety Notes

  • Must be installed with proper insulation and fuses

  • Keep sensors dry and clean for accurate readings

  • Avoid placing sensors directly near heating or humidifying elements.

STC-3028 Basic Operation Overview

  • The controller has 2 relay outputs:

    • One for temperature control

    • One for humidity control

  • The screen shows:

    • Red display = Current temperature

    • Blue display = Current humidity

Button Functions

Button Function
SET Enter setting mode / Confirm values
▲ Increase value / navigate options
▼ Decrease value / navigate options

How to Set the Target Temperature

  1. Short press SET

  2. The red display (temperature) will start blinking.

  3. Use ▲ or ▼ to set your target temperature (e.g., 37.5°C for an incubator).

  4. Wait 3–5 seconds or press SET again to confirm.

How to Set the Target Humidity

  1. Long press SET for ~3 seconds to enter advanced settings mode.

  2. Use ▲ or ▼ to scroll to H (Humidity setpoint).

  3. Press SET → the blue display will blink.

  4. Use ▲ or ▼ to adjust the target humidity (e.g., 60% RH).

  5. Press SET again to confirm.

  6. Wait or scroll to E to exit the menu.

Other Useful Settings

Code Description Example Value
d Temp hysteresis (range) 1.0°C
H Target humidity 60% RH
C Humidity hysteresis 5%
HC Humidity control mode H=Humidify / D=Dehumidify
TC Temp control mode H=Heat / C=Cool

To toggle heating vs cooling (or humidifying vs dehumidifying), set TC or HC accordingly.

Example Setup (Poultry Incubator)

Setting Value
Temp target 37.5°C
Temp mode Heat (TC=H)
Humidity 55% RH
Humid mode Humidify (HC=H)
Temp range 0.5°C (d=0.5)
Humidity range 5% (C=5)

if you want to see how to ste and connect it you can watch this video can be helpful for you

 Specifications :

Parameter Value
Power Supply 220V AC ±10%
Temperature Range –40°C to +120°C
Humidity Range 0% to 100% RH
Temperature Accuracy ±1°C
Humidity Accuracy ±3% RH
Relay Output 2 Relays (Temp & Humidity)
Sensor Type Combined Temp + Humidity sensor
Control Mode ON/OFF Control (Relay switching)
Display Dual LED (Red = Temp, Blue = RH)
Size ~75 x 55 x 30 mm
Mounting Panel mount

Based on 0 reviews

0.0 overall
0
0
0
0
0

Only logged in customers who have purchased this product may leave a review.

There are no reviews yet.

Related Products